Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 2.400 – 2.4835 GHz, the TX power is limited to 20dBm (EIRP).Datasheet for any device is available on the official manufacturer website.For Outdoor Usage: End-user requires approval/license from the NTRA.In case WLAN devices work with different ranges than the above regulations, then a customized firmware version from the manufacturer/supplier is required to be applied to the end-user equipment and also prevent the end-user from reconfiguration.The Frequency band 5.470-5.725 GHz isn’t allowed for commercial use.Other operating systems have not been tested. The device supports RouterOS software with the version number at or above what is indicated in the RouterOS menu /system resource. Useful for RouterBOOT debugging and recovery. Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Release the button after LED is no longer lit (~20 seconds) to cause a device to look for Netinstall servers (required for reinstalling RouterOS over the network).Release the button when the LED turns solid green to clear all configuration and defaults.Release the button when green LED starts flashing, to reset RouterOS configuration to defaults.See this page for connection and configuration guides: Reset button Please connect with your web browser to this IP address to configure it. All other models all the ports are switched.īoth models can be accessed through the IP 192.168.88.1, the username is admin and there is no password.Eth1 and SFP1 have DHCP client configured. CRS109-8G-1S-2HnD-IN: ports 2-8 are switched, wireless interface and switch are bridged, and bridge contains a DHCP server.For recovery purposes, it is possible to boot the device from the network, see a section Reset button. In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address of the device from the LAN side (all access is blocked from the Internet port by default). We suggest starting here to get yourself accustomed to the possibilities. RouterOS includes many configuration options in addition to what is described in this document. For wireless models, please make sure you have selected the country where the device will be used, to conform with local regulations. Once logged in, we recommend clicking the “Check for updates” button in the QuickSet menu, as updating your RouterOS software to the latest version ensures the best performance and stability. Standard RJ45 to COM cable can be used, pinout can be found here: Configuration The device is equipped with an RJ45 serial port, set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity. For CRS212: Ten SFP cages, one SFP+ cage, one Gigabit Ethernet port. For CRS210: Two SFP+ cages, SFP+1 compatible with 1.25G and 10G, SFP+2 compatible 10G SFP modules only.For CRS112: Four SFP cages, compatible with 1.25G SFP modules.For CRS109: One SFP cage, compatible with 1.25G SFP modules, Built-in 802.11b/g/n 2GHz wireless access point.Except for CRS212: Eight (8) 10/100/1000 (Gigabit) Ethernet ports (Auto MDI/X).passive PoE input: 8-56V (injector included).Įxcept for CRS212-1G-10S-1+IN, which only accepts 8-30V direct input, with no PoE input support Extension slots and ports.direct-input power jack: 8-56V (24V 0.8A PSU included),.The devices accept power in the following ways: Set up your password to secure the device.Updating software will ensure the latest security fixes and regulations set by local law.Open Winbox and upload packages in the Files menu.Choose your architecture (MIPSBE) and download the latest packages from any channel to your PC.To manually update the device, go to our download page. The device needs to have an active internet connection.
0 Comments
Leave a Reply. |